TRUMSYNT-16 1.4

- The trial is now 14 days, with 5 seconds of silence every minute from the
  first day; after 14 days the plug-in makes no sound until a license is
  installed. A license removes both, in TRUMSYNT-16 and TRUMSYNT-KIT. Anyone
  who tried an earlier version gets a fresh 14-day trial the first time 1.4
  opens.
- Nine new LFO destinations: CLICK TUNE, NOISE DEC, CLICK DEC, VEL, PITCH,
  VCO1 LVL, VCO2 LVL, VCO1 PITCH EG and VCO2 PITCH EG. PITCH moves both
  oscillators together while the sound rings, with the same depth as VCO1
  PITCH and VCO2 PITCH; the click keeps its own tuning. VEL scales each hit's
  velocity as it plays, so level, click and the velocity-driven VCF decay all
  follow it.
- MOD A and MOD B can now also reach VCO1 LVL, VCO2 LVL, VCO1 PITCH EG and
  VCO2 PITCH EG.
- LFO SYNC now plays in time. RATE steps through eight note values (4 bars,
  2 bars, 1 bar, 1/2, 1/4, 1/8, 1/16 and 1/32) and the LFO is locked to the
  bar: to the DAW's position while it plays, and to the sequencer's own clock
  under RUN. Presets saved with SYNC on keep their RATE, read as the nearest
  note value, but now sound in time.
- SH with RETRIG on takes a new random value at every hit, from the sequencer
  or MIDI, instead of holding one value. Together with VEL this gives every hit
  its own random velocity.
- Turning RESONANCE no longer crackles on a ringing sound.
- Undo: Cmd+Z (Ctrl+Z on Windows) undoes the last edit made in the editor, up
  to 100 edits: a whole knob movement, a button, a menu choice, a pasted value,
  a preset load or INIT. Host automation and RUN/STOP are not part of it.
- Copy and paste sequencer values: point at a step knob and press Cmd/Ctrl+C,
  then point at another and press Cmd/Ctrl+V. PITCH pastes to PITCH, VELOCITY
  to VELOCITY, and MOD A and MOD B between each other.
- Value readout: press V to switch it on or off. While it is on, a knob you
  hold shows its value, and a synced LFO RATE reads as a note value. The
  setting is saved with the project, not in presets.
- The DAW's own parameter fields and automation lanes now show values in
  their units, in the same words as the value readout: 1.5 kHz, 50 ms,
  +3.0 st, 72 %, x1.50, and a note value such as 1/4 for a synced LFO RATE.
  A value typed into the DAW is read in the unit it is shown in, so 50 in a
  decay is 50 ms and 72 in an amount is 72 %; a unit can be typed too, as in
  1.5 kHz or 0.5 s. Text that is not a value leaves the parameter as it was.
  Projects, presets and automation keep their values.
- New look for the lit LEDs, the popup menus and the preset browser, and the
  knob indicators now line up with the panel art.
- Presets and projects saved with earlier versions keep their LFO and MOD
  destinations.

TRUMSYNT-16 1.3.1

- The step-length list for a lane no longer offers lengths a single page cannot
  reach. Lengths above 8 stay available while A + B is lit.
- A sequencer that was switched in when a project was saved now starts with the
  DAW transport in hosts that bring plug-ins up only when playback begins.
  Before this it stayed switched out until RUN was pressed on it.

TRUMSYNT-16 1.3

- RESET is now a mode switch. Press it while the sequencer is stopped and the
  lamp stays lit: the sequence then returns to step 1 every time playback
  starts, from the DAW transport or from RUN/STOP. Pressing RESET while the
  sequence runs still resets it immediately, as before, and the lamp blinks to
  acknowledge the press.
- RUN/STOP now shows three states: lit while the sequence sounds, pulsing while
  the sequencer is switched in and waiting for the transport, dark when it is
  switched out. Switching the sequencer out with the transport stopped no longer
  starts it first.
- Double-click RUN/STOP to run the sequencer without the DAW transport.
- Switching the sequencer in while the DAW is playing now comes in on the next
  step instead of under the click, and the sequencer's own clock restarts on a
  whole step.
- Loading a preset no longer switches the sequencer back on.
- MIDI CC 110 starts and stops the sequencer's own clock while the DAW transport
  is stopped.
- A project saved before the plug-in recorded which bank a preset came from now
  reopens with its own sound, instead of a factory preset being written over it.
- Fixed recalled editor size so older host state cannot overwrite a valid window
  size with zero dimensions.

TRUMSYNT-16 1.2

- Fixed host preset-program mapping so newly saved user presets no longer fall
  back to the last factory preset in hosts that expose plug-in programs.
- Fixed large-knob indicator alignment while resizing the plug-in window.
- macOS README now gives a Finder-first install path before the Terminal method.
- Local deploys now replace installed bundles instead of merging into them.

TRUMSYNT-16 1.1

- The plug-in now installs its own factory presets on first run and keeps them
  up to date. No separate installation step.
- A license file that is present but unreadable is now reported as such,
  instead of as an expired demo.
- Faster first scan in the host: the plug-in no longer waits on preset files
  while a DAW is scanning it.
- Temporary files are no longer listed in the preset browser.
- Preset bank names are matched without regard to upper and lower case.

TRUMSYNT-16 1.0

- Initial macOS release package.
- AU and VST3 formats.
- Universal Apple Silicon and Intel binaries, macOS 12 or later.
- Offline license-file unlock.
- 7-day full-featured demo before demo expiry.
- Factory preset bank included.
